VIDEO MAGAZINE SERIES 3

VIDEO MAGAZINE SERIES 3
"THE WOOD INDUSTRY VIDEO JOURNAL"
(18 VIDEO SELECTIONS)

Note: many of the "INTERESTING IDEAS" shown in this series were summarized in videos R3 and R4 in the series "VIDEOS ON SELECTED WOOD INDUSTRY TECHNOLOGIES"

ISSUE 1. - WOOD INDUSTRY VIDEO JOURNAL
FEATURES
Explanation of the cut-off saw backgauge
Lumber defecting procedures
Use of a pop-up fence on a straight line ripsaw
Ripping procedures to minimize edge waste
Use of a flip-stop on a straight line ripsaw
INTERESTING IDEAS
Lumber infeed system to a cut-off saw
Cut-off saw with two buttons for activation
Cut-off saw with rapid stroke speed
Scissors lift
Check list inspection system for rough mills
Use of go or no-go gauges at ripsaws
Lumber in-feed system at ripsaws
"Barrel" humidifier
Ripsaw carts
Salvage saw carts
Salvage saw with stops mounted on both sides of the saw
P.V.C. pipe strips used to separate stock at gluing machine
Costs and benefits of the Wood Industry Video Journal
English Only. Order Video J1. $79.95

ISSUE 2. - WOOD INDUSTRY VIDEO JOURNAL
FEATURES
Barr-Mullin's "Compugauge"
Secondary yield losses
Panel width allowance reduction
Use of thin kerf saws
Length trim allowances
Use of a bandsaw for reripping
Reduction of moulder allowances
Patching defects
Marking of "set-up" pieces
Check counts
Check widths
Bandsaw losses and ways to reduce them
Use of splitter saws on moulders
INTERESTING IDEAS
Bandsaw cutting jig
R.F. shuttle press
Lightweight ripping fence for straight line ripsaws
Pop-up fence for straight line ripsaws (with a rubber band)
Floor sweeper
Reduction of glue costs by mixing different glues
Mufflers on torque wrenched at a glue reel
English Only. Order Video J2. $79.95

ISSUE 3. - WOOD INDUSTRY VIDEO JOURNAL
FEATURES
Montornes computer controlled cut-off saw
Drawer building operation at Jamestown Sterling Corp. (also shown in video R10)
Tour of Roundwood Corporation's unique "sawmill" for cutting furniture "rounds"
INTERESTING IDEAS
Stacker for panel lay-up operation at Smith, Inc.
Coupling tenon machines and reversing turning direction of the cutterhead
An automatic sticker catcher
Multiple operation of lathes
FEATURES
Rapid cut-off saw operator at Jamestown Sterling Corp. (also shown in video R10.)
Dr. R. Bruce Hoadley's film on wood shrinkage (also shown in video R5)
English Only. Order Video J3. $79.95

ISSUE 4. - WOOD INDUSTRY VIDEO JOURNAL
FEATURES
Interholtz Raiman gang ripsaw and new ripping procedure
Wood waste handling systems (tour with Laidig representative)
Century Furniture Co.
Conover Chair Co.
Statesville Brick Co.
North Carolina furniture company
Singer Furniture's baling system
Tour of C.F. Martin Company's Sawmill
INTERESTING IDEAS
Door with spring on wood waste unloading system
Wood waste conveyor
Bolster clips (for lumber piles)
Lumber pile cover hold-down clips
Lumber piling system with powered rubber roller
FEATURE
A "high speed" film of wood machining showing the effect of knife angles and depth of cut
English Only. Order Video J4. $79.95

ISSUE 5. - WOOD INDUSTRY VIDEO JOURNAL
FEATURES
The Telemobile lumber handler
Marunaka lumber slicer
INTERESTING IDEAS
Inflate-A-Fork (a unique device for "splitting" lumber stacks)
Lumber stacking system at Temple Stuart Co.
Panel sizing system at Temple Stuart Co.
Bark bagging system at Roundwood Corp.
Condensate return storage tank at Smith, Inc.
Reduce glue costs by mixing different glues
Portable stick jig for lumber piling
English Only. Order Video J5. $79.95

ISSUE 6. - WOOD INDUSTRY VIDEO JOURNAL
FEATURES
Vacutherm, Inc. - vacuum drying systems
Forester Manufacturing Company
Speed lathes
Button lathe
Italian lathe
INTERESTING IDEAS
A log tagging (identification) system
Use of a lubricant in a lumber slicing operation
A car shower (washing) system at a woodworking plant
Sizing saw used at a glue reel
FEATURE
Computer controls for dry kilns
Dollco
Hildebrand
English only. Order VIDEO J6. $79.95

ISSUE 7. - WOOD INDUSTRY VIDEO JOURNAL
FEATURE
Tour of Andover Wood Products of Maine
Log yard
Sawmill and bolter mill
Lumber stacking and yard
Unique "Envelopes" for lumber piles
Dry kilns
Dimension plant
Cut-off saw line
Ripsaws
Turn table for scrap and salvage
Glue reels
Wrapping machine
INTERESTING IDEAS
"Back turners" on sawmill for rapid log turning
Storage area at cut-off saws for lumber
Hole in ripsaw dust collection pipe which reduces kick-back problem
Durable metal floors in dimension plant
Color marking of loads
"Rope" hold down device for factory trucks
Use of a blackboard at the ripsaws
Chipping and sale of excess waste materials
Protective coating for glue reels
Preventing panels from sticking together
Use of a mirror at the glue reel
Protective cage for the fork lift
Reward for best safety slogan
Use of flue gasses to dry wood waste
FEATURE
Incentive paid workers at S. Bent's Chair factory.
Hand chucking operation
Chair assembler
Stain wiper
Sealer sprayer
Sealer sander
Chair packing
English Only. Order Video J7. $79.95

ISSUE 8. - WOOD INDUSTRY VIDEO JOURNAL
FEATURE
Tour of Bethel Furniture Stock, Inc.
Log Yard, sawmill and lumber yard
End coating practices
Predrier, dry kilns and storage sheds
Wood waste storage bins, boiler and dutch oven burner
Cut-off saw with Compugauge, busting saw and planer
Unique ripping system
Panel lay-up and efficient glue reel operation
Planing, sizing and wrapping of panels
Explanation of the Seavey Backknife lathe
INTERESTING IDEAS
Use of an ammeter to check saw dullness
Automatic soot cleaners for fire tube boilers
Factory trucks with built in scissors lifts
Panels glued with water resistant glues used as bending stock
Sonic humidifiers
English Only. Order Video J8. $79.95

ISSUE 9. - WOOD INDUSTRY VIDEO JOURNAL
FEATURE
Excerpt on mould sanding from the Norton Company film "Mechanized Wood Sanding"
Block making
Breaking-in sanding belts
Mould sander
Auto feeding round table tops
Spool sanding, disc sanding
Sanding carvings, Flutter sanding, brush sanding
INTERESTING IDEAS
Fence system for ripping long stock
Cleaning of abrasive belts on wIde belt sanders by using "dummy" panels
Storage of abrasive belts
Jaw bolt wood connector
FEATURE
Excerpt from a supervisory development seminar conducted by Mr. Roy Hatten for Henredon Furniture Industries, Inc.
English Only. Order Video J9. $79.95

ISSUE 10. - WOOD INDUSTRY VIDEO JOURNAL
FEATURE
Dr. R. Bruce Hoadley of the University of Massachusetts discusses wood and its structure
Productivity losses which occur because of handling time and ways to reduce these losses
INTERESTING IDEAS
Use of rubber to clean sanding belts
Retrofit backknife lathes to save wood materials
and chuck tenon through the "nubbin"
Rough mill supervisor changes cut-off saw setup to save wood
Use of heat exchangers to conserve energy in dry kilns
FEATURE
Excerpt from Roy Hatten's seminar on supervisory development for Henredon Furniture Industries, Inc.
Excerpts from Woodworking Machine Operators Training Programs
English Only. Order Video J10. $79.95

ISSUE 11. - WOOD INDUSTRY VIDEO JOURNAL
FEATURE
Handling losses by a tennis racket manufacturer
Productivity losses which are due to delays or production imbalances
Excerpts from Roy Hatten's seminar on surervisory development
INTERESTING IDEAS
Inspection of a lumber stacker
A sander for "ball" turnings
Modified straight line ripsaw used as a busting saw
Yield incentive plan for supervisors
FEATURES
Dr. R. Bruce Hoadley discusses Wood Technology
Shrinkage and swelling of wood
Warpage
Excerpt from "on the job" training program
English Only. Order Video J11. $79.95

ISSUE 12. - WOOD INDUSTRY VIDEO JOURNAL
FEATURES
Kupfer Muhle self centering planer
Film on the "Shrinkage of Pine"
INTERESTING IDEAS
Ripping tapored parts for increased yield
Use of a projector lamp at panel layup stations
Collapsable container tanks
Use of tables at salvage saw to increase efficiency
FEATURE
Roy Hatten's seminar on supervisory development
English Only. Order Video J12. $79.95

ISSUE 13. - WOOD INDUSTRY VIDEO JOURNAL
FEATURE
Discussion of a "Gain Sharing" employee wage incentive plan with wood industry consultant Ross Associates, Inc.
INTERESTING IDEAS
Need for a table at a jointer
Need for a table at a variety saw
Use of a table at an edge sander
Table dropped at an edge sander
Prepositioning stock at a belt sander permits one-way handling
Use of a "c-clamp" improves handling efficiency
Tossing pieces into box improves handling time
Need for a scissors lift to improve handling
Upholstery tagging system
Use of a light for product inspection
A packing system for desks
FEATURE
"System Six" sawing system
English Only. Order Video J13. $79.95

ISSUE 14. - WOOD INDUSTRY VIDEO JOURNAL
FEATURE
Use of hydraulic cutterheads
Interview with Al Brown of Forest City Tool Co.
Visit to Hickory Manufacturing Co.
INTERESTING IDEAS
Optical comparison device at Hickory Manufacturing Co.
Air knives for belt sanders
Gas fired heating system at Kittinger Co.
Scissors lifts at Kittinger Co.
FEATURE
Geiger copy shaper
English Only. Order Video J14. $79.95

ISSUE 15. - WOOD INDUSTRY VIDEO JOURNAL
FEATURE
Department of Wood and Paper Science, North Carolina State University
Dr. Richard Thomas explains the Department's program
Veneer checking project
Moisture pallets for lumber drying
Use of a compressometer at the glue reel for checking gluing pressures
A shaper for abrasive wheels
Machining studies
Laminated veneer project
Troubleshooting gluing problems
Lathe automation project
English Only. Order Video J15. $79.95

ISSUE 16. - WOOD INDUSTRY VIDEO JOURNAL
FEATURES
Maintenance checks for the Diehl straight line ripsaw
An automated feeding, glue spreading and unloading system for electronic gluing machines
INTERESTING IDEAS
Reduction of Brown Stain in White Pine lumber
Use of Oxalic acid to wash off lumber stain
Use of exterior grade plywood for fan decking and baffles in dry kilns
Patching holes around pipes which pass through kiln walls
English Only. Order Video J16. $79.95

ISSUE 17. - WOOD INDUSTRY VIDEO JOURNAL

Note: This video is the same as video R6E, "Troubleshooting the Dry Kiln and Its Controller". See listing of "Videos on Selected Wood Industry Technologies"

ISSUE 18. - WOOD INDUSTRY VIDEO JOURNAL
FEATURES
Wood Industry Consultant Art Raymond explains numerically controlled woodworking machines and discusses history, types, operating procedures and applications for this type of equipment.
Visit to Cochrane Furniture Co. of Warrenton, NC to inspect a Torwegge tenon machine which is equipped with numerical control. Critical elements such as set-up time and costs are pointed out.
English Only. Order Video J18. $79.95

[ Home | Subject Search | Full Listing | Order Form ]